DIAMOND PROTECH PRO HYDRO2 HYPER SLICK HYDROPHOBIC TOP COAT 30ML

Why buy this product?
Quick application time.
Only for certified PRO installers.
Hyper slick hydrophobic top coat.
Available in 30ml and 50ml.

About this product
Diamond ProTech Pro HYDRO² is the top coat for the nano diamond coatings PRO range. HYDRO² protects your vehicle against the elements while adding an hyper slick hydrophobic top coat that offers ultimate water beading. HYDRO² will prevent water spots and gives your car the ultimate shine and gloss.

Diamond ProTech’s Pro Line requires training and is exclusively available for certified PRO installers.

Application tips from Diamond ProTech
- Apply in temperatures between 10-30°C.
- Apply in a closed, well ventilated, indoor area with air humidity not exceeding 70%
- Cover and seal all windows
- PRO 120 SPRAY requires IR Curing Lamps
- Clean spray gun with PRO SOLVENT SPRAY (Spray Gun Cleaner) between products and immediately after applying PRO HYDRO SPRAY to avoid any permanent damage to the spray gun.
- Must wear protective gloves and appropriate respirator.

Products you need for applying Pro Hydro
- 4 Microfiber Towels
- Spray Gun & Diamond ProTech Adapter
- Protective Gloves
- Respirator Mask
- Diamond Body Prep

IR CURING LAMP INSTRUCTIONS
- Temperature: 50-60°C
- Distance to bodywork: 60-70 cm / 24-28 inches.
- Time: 15-20 minutes for each section.

Note
- To ensure the best & safest application process, make sure you have the following before applying: 4 microfiber towels, protective gloves, respirator, diamond body prep
- If applying in high heat or high humidity, lower time between application and removal. Test over a small area to determine appropriate time to let the coating bond to the surface.
- If the product “sweats” for an extended period and begins to dry on the surface or is difficult to remove, re-wet the area with more product and immediately buff off.

How to use
- Wash, polish and treat areas to be coated with Diamond Body Prep.
- Shake the bottle of PRO 120 A for 15 seconds. Connect the bottle to the Diamond ProTech adapter and then to the IWATA LPH-80 spray gun. Spray PRO 120 SPRAY A evenly over 3-4 sections of the car. Partially overlap each pass over the previous to insure full coverage.
- Wait 10-15 mins and buff off excess with a short - piled microfiber towel.
- Clean the spray gun with PRO SOLVENT SPRAY to prepare for PRO 120 SPRAY B.
- Wait 1 hour to allow PRO 120 SPRAY A to bond before applying the next layer: PRO 120 SPRAY B
- Shake the bottle of PRO 120 SPRAY B well for 15 seconds. Connect bottle to the Diamond ProTech adapter and then to the IWATA LPH-80 spray gun. Spray PRO 120 SPRAY B evenly over 1-2 sections of the car. Partially overlap each pass over the previous to insure full coverage. Wait 1-3 mins and buff off excess with a low-nap microfiber towel. Clean the spray gun with PRO SOLVENT SPRAY to prepare for PRO HYDRO SPRAY.
- Diamond ProTech recommends using IR curing lamps to accelerate the curing process.
If no IR curing lights are used, wait four hours to allow PRO 120 SPRAY B to dry before applying the next layer, PRO HYDRO SPRAY.
- Shake the bottle of PRO HYDRO SPRAY well for 15 seconds and connect the bottle to the Diamond ProTech spray adapter and then to the IWATA LPH-80 spray gun. Proceed to spray PRO HYDRO SPRAY evenly over 3-4 sections of the car. Partially overlap each spray pass over the previous one to insure full coverage.
- Wait 7-10 mins and buff off excess with a low-nap microfiber towel.
- Clean spray gun with PRO SOLVENT SPRAY when finished. Allow coating system to cure for 2 hours before using the vehicle.

Specifications